Mobile Welding Burnaby: How to Hire and Prepare

A practical checklist for booking an on-site welder in Burnaby and the Lower Mainland: photos, access, permits, weather and when a shop job is the better call.

Quick answer: Mobile welding in Burnaby means a certified welder drives a fully equipped welding truck to your job site, yard, dock or facility and repairs or builds the steel, stainless or aluminum where it sits. It saves you the cost and downtime of hauling heavy equipment or cutting out installed work. To get it done right, send clear photos, confirm truck access and set-up space, and book with a qualified, certified welder.

If you're searching for mobile welding Burnaby, you probably have something that can't easily move: a cracked excavator bucket, a broken trailer frame, a gate that's already hung, or a pipe run already in the ceiling. Berto's mobile welding service has served Burnaby and the Lower Mainland since 2019 with both mobile and shop welding. Work is led by a Red Seal A Class Pressure Pipe Welder, and the rig is a self-contained welding truck with an engine-driven welder, cable reels and a full stock of tools and consumables.

Most local welding pages tell you what they weld. This guide covers what they usually skip: how to prepare your site, what to have ready before you call, when a shop job beats a mobile one, and the safety and permit questions that can delay a job on the day.

What mobile welding covers in Burnaby

Common on-site jobs include:

  • Heavy equipment and attachments: buckets, blades, brackets, hitches and frames
  • Trailers and truck decks: flatbeds, mounts, racks and tool box brackets
  • Structural steel: beams, columns, base plates, canopies, mezzanine framing and stair stringers
  • Gates, railings, fences and security bars for homes, strata and commercial buildings
  • Field pipe welding, including Red Seal A Class pressure pipe work
  • Aluminum and stainless repairs, including marine work at the dock
  • Maintenance and shutdown support for industrial and commercial facilities

7 steps to hire and prepare for a mobile welder in Burnaby

1. Define what's broken or what needs building

Write down the part, the material (steel, stainless or aluminum, if you know), and what happened: a crack, a snapped weld, wear, or a new piece to fabricate. Note whether the item carries load or pressure. Structural and pressure work needs a welder qualified for it, so this detail matters from the first call.

2. Take good photos and measurements

Photos are the single most useful thing you can send. Take one wide shot showing where the item sits and how a truck could reach it, plus close-ups of the damage. Add a tape measure in the frame for scale. Good photos help the welder bring the right material and consumables the first time, which avoids a second trip.

3. Check the welder's qualifications

Ask what certifications the welder holds and whether they suit your job. For pressure piping, look for a pressure-qualified tradesperson; Berto's work is led by a Red Seal A Class Pressure Pipe Welder. For structural work, ask about CWB certification. Also confirm the company carries liability insurance and that WorkSafeBC coverage is in place for anyone working on your site.

4. Confirm access and parking

A mobile rig needs to park as close to the work as possible so leads can reach it. Before booking, check:

  • Height clearance for parkades or covered loading bays
  • Gate codes, security sign-in and site hours
  • Distance from the nearest truck spot to the work
  • Strata or building rules for contractors

In dense parts of Burnaby, such as Metrotown and Brentwood towers, loading-bay bookings can take a day or two. Sort them out early.

5. Ask about hot work permits and fire safety

Many commercial, industrial and strata buildings require a hot work permit before any welding, cutting or grinding. This is usually issued by the building owner, property manager or site safety lead, not the welder. Find out who signs it and whether a fire watch is required after the work. Move flammables away from the work area and know where sprinkler heads, smoke detectors and fire extinguishers are.

6. Prepare the work area

Clear the area around the repair, drain or isolate anything that held fuel, oil or hydraulic fluid, and lock out equipment so it can't start or move. If people will be nearby, plan for them to stay back from the arc; a professional welder will use screens or blankets to protect others. Clean off heavy grease and mud if you can. It saves billable time.

7. Book, confirm scope, and do a walkthrough

Call with your details and photos. A good welder will confirm scope and timing and flag anything that affects the job, such as access, parking or materials. Berto's books mobile work with a 4-hour minimum, which covers travel and set-up on short jobs and gives time to finish most repairs properly. When the work is done, walk through it together before the rig leaves.

Before-you-call checklist

  • Description of the problem and the material (if known)
  • Wide photo showing access, plus close-up photos of the damage
  • Rough measurements of the part or area
  • Site address, parking details, gate or loading-bay access
  • Hot work permit requirements and who signs off
  • Equipment locked out and fluids drained or isolated
  • Flammables cleared from the work area
  • Site contact name and phone number for the day
  • Preferred date and how urgent the job is

Mobile vs shop welding: which do you need?

Not every job should be done on site. Here's how the two compare:

FactorMobile weldingShop welding
Best forHeavy equipment, installed structures, gates, pipe runs, anything hard to moveNew fabrication, precision parts, items you can easily bring in
TransportNone; the rig comes to youYou (or a hauler) bring the item in
DowntimeUsually lower for large equipmentIncludes loading, transport and pickup time
Working conditionsDepends on weather, access and site rulesControlled environment, full equipment on hand
PermitsHot work permit may be needed on your siteHandled inside the shop
BookingBerto's: 4-hour minimumCall for a quote
PricingCall for a quoteCall for a quote

A common approach is a hybrid: fabricate new railings, brackets or frames in the shop, then install and weld them in place on site. Berto's offers both, so one company can handle the build and the install. For service details and booking, see our mobile welding page.

Weather and timing in the Lower Mainland

Rain is a real factor for outdoor welding in Burnaby, especially through fall and winter. Wet surfaces, wind and cold steel all affect weld quality. Ask your welder how they handle weather. Covered areas, tarps or a dry window may be needed, and a job may need to be rescheduled for safety and quality. Let the welder know if the work is fully outdoors when you book.

Larger jobs and shutdowns

For commercial and industrial projects, shutdowns or tight schedules, one welder may not be enough. Berto's can supply crews of up to 15 certified welders, so you make one call and get a coordinated crew instead of chasing individual subcontractors. For shutdowns, book as early as possible and share the schedule, scope and site safety requirements up front.

Service area

We're based in Burnaby and bring the rig across the Lower Mainland, including Vancouver, Surrey, New Westminster, North Vancouver, West Vancouver, Coquitlam, Port Coquitlam, Port Moody, Richmond, Delta, Langley and Maple Ridge.

Frequently asked questions

How much does mobile welding cost in Burnaby?

Pricing depends on the job: material, access, travel and time on site. Berto's books mobile work with a 4-hour minimum. Call 236-243-8484 with photos and details for a quote.

Is mobile welding as strong as shop welding?

Yes, when it's done by a qualified welder using the right process and preparation. Shop welding gives more control over conditions, so some fabrication is better built in the shop and installed on site.

Can a mobile welder work on aluminum and stainless steel?

Yes. Berto's mobile rig handles steel, stainless and aluminum, including marine repairs at the dock. Tell us the material when you book so we bring the right consumables.

Do I need a permit for on-site welding in Burnaby?

It depends on the site. Many commercial and industrial buildings require a hot work permit from the owner or property manager. Check with your building or site management before the welder arrives.

What areas does Berto's Welding serve?

We're based in Burnaby and serve the Lower Mainland, including Vancouver, Surrey, New Westminster, North Vancouver, Coquitlam, Richmond, Port Moody, Delta, Langley and Maple Ridge.

Get a quote

Need mobile welding in Burnaby? Call Berto's Welding Ltd. at 236-243-8484 with your photos and job details. Pricing is job-dependent, so call for a quote.

Ready to Book On-Site Welding?

Send photos and the site details, then call or book online. Berto's will confirm scope and timing.

236-243-8484