Gate Welding in Vancouver

On-site repairs for gates, railings and stairs. We come to the gate, or build a section in the shop when it can come off.

  • On-site repairs
  • 4-hour mobile minimum
  • Steel, aluminum & wrought iron

Quick answer: Gate welding in Vancouver is usually a repair to a gate, railing or stair that's already in place: a sagging leaf, a torn hinge, a cracked frame or a loose post. Cost depends on the metal, the access, how much rust or damage there is, and whether we weld it on site or in the shop. Call Berto's Welding at 236-243-8484 for a quote; pricing is job-dependent.

If you're looking for gate welding in Vancouver, you probably want the gate you have to close properly again, or a strata railing that's come loose at the base — not a brand-new install. Berto's Welding Ltd., based in Burnaby since 2019, offers mobile gate welding Vancouver-wide, gate welding in Burnaby, and shop work when a section can come off. We're CWB certified, and work is led by a Red Seal A Class welder. This page is for homeowners, strata councils and property managers who need a repair.

What we repair

Most calls are gate repair welding, metal gate repair and railing repair welding on metalwork that's already hung:

  • Sagging leaves, torn hinges and cracked frames
  • Latch or drop-rod problems tied to a bent frame
  • Posts cracked at the base or worked loose from a plate
  • Security gate welding and repairs to security bars
  • Railing welding in Vancouver: loose posts, cracked welds and base plates
  • Stair stringers, handrails and guards that have corroded or come loose

If a new section has to be made, we can fabricate it in the shop and weld it in place.

Repair or replace?

A weld will not fix everything. Sometimes the honest answer is a new leaf, post or section of rail.

FactorRepairReplace
When it makes senseThe frame is still sound and the damage is localRust has eaten through the frame, posts have failed, or the same repair keeps coming back
TimeOften finished in a single on-site visitA new section is usually built in the shop, then fitted; that takes longer
CostUsually lower when the damage is localHigher, but the right call when the structure itself has failed
Where the work happensUsually on site for hung gates and railingsShop fabrication, then installation on site

We'll say if a repair won't last, rather than weld something that will fail again.

What drives gate welding cost

There is no flat rate. Gate welding cost is driven by:

  • The metal. Steel is the most straightforward. Aluminum needs TIG welding and a clean joint. Wrought iron may not behave like mild steel, so we need to know what you have.
  • Access. A driveway gate at ground level is quicker than a courtyard gate or a stair railing in an occupied building.
  • Condition. Paint, rust and old repairs have to be ground back to clean metal. Prep often takes longer than the weld.
  • Travel and set-up. Mobile visits include loading the rig, driving, parking and protecting the area.
  • Site rules. Hot work permits and fire watch on strata and commercial buildings add time.

Mobile welding is booked with a 4-hour minimum. Shop work has a 2-hour minimum. See how much mobile welding costs, or call 236-243-8484 for a quote.

Mobile gate welding: we come to the gate

A hung gate or a fixed railing is a poor candidate for the shop. Taking it down and hanging it again can cost more than repairing it where it stands. That's why most of this work is mobile welding: the truck comes to your home, strata or building. Details for Vancouver jobs are on our mobile welding in Vancouver page. The rig has its own engine-driven welder, so you usually don't need to supply power. If a short section has to be made first, we can build it in the shop and bring it with us.

Strata railings, stairs and occupied buildings

Property managers and strata councils often call about a loose parkade guard, a cracked stair rail, or a pedestrian or security gate that won't close. These usually have to be fixed in place while the building stays in use.

  • Hot work permits. Many occupied buildings require a permit from the owner or property manager before welding, cutting or grinding, and some require a fire watch afterwards. Find out who signs it before the welder arrives.
  • Access and parking. Parkade height, loading-bay bookings and stair access can decide the schedule.
  • Batch the list. Several small repairs in one visit use the 4-hour mobile minimum better than separate call-outs. Send a list with photos.

Steel, aluminum and wrought iron

We weld steel, aluminum and wrought iron, and stainless when that's what is already on the building. Steel is the most common repair in Vancouver's climate, usually at rusty post bases and old welds. Aluminum needs TIG welding and more prep, so tell us if that's what you have. Many "wrought iron" gates are mild steel with a decorative pattern; some older pieces are a different metal. A photo helps, because the process and filler have to match.

How long a repair takes

Many gate and railing repairs are finished in a single visit, within the 4-hour mobile minimum, if access is clear and the metal is in reasonable condition. It takes longer when rust has to be cut out and a new section fabricated, when the gate has to be re-hung, or when a strata site needs a permit. Send photos and a note on access, and we'll give you a clearer picture before we book.

How to get a gate or railing repaired

  1. Photograph the damage and the whole gate or rail. Take a wide shot of the gate or railing in place, plus close-ups of the damage with a tape measure for scale.
  2. Note the metal, if you know it. Steel, aluminum, wrought iron or stainless — or say if you're not sure.
  3. Decide whether it can come off. Most hung gates and fixed railings should stay put. If a section unbolts easily, shop work (2-hour minimum) may be the better repair.
  4. Check site rules. Homeowners: think about parking and neighbours. Stratas and property managers: confirm the hot work permit, fire watch, resident notice and access before the visit.
  5. Bundle other repairs. List every gate, rail or stair that needs work so they can be done in the same booking.
  6. Clear the work area. Move cars, bins and anything flammable away from the weld. Unlock gates and have a site contact on hand.
  7. Call or book and confirm the scope. Call 236-243-8484 or book online. Send the photos, the address and any permit details.

Before-you-call checklist

  • Wide photo and close-ups of the damage, with a tape measure for scale
  • Metal, if known (steel, aluminum, wrought iron, stainless)
  • Is it a swing gate, sliding gate, security gate, railing or stair?
  • Can any part come off, or must it be welded in place?
  • Site address, parking and access (parkade height, codes, loading bay)
  • Hot work permit needed? Who signs it?
  • Other gates or railings to bundle into the same visit
  • Preferred dates and how urgent the repair is

Where we work

We're based in Burnaby and serve Vancouver, Burnaby, Surrey, Richmond, North Vancouver, West Vancouver, Coquitlam, Port Coquitlam, Port Moody, New Westminster, Delta, Langley and Maple Ridge. See all service areas.

Hours are Monday to Friday 7:00 a.m. to 3:30 p.m. and Saturday 8:00 a.m. to 2:00 p.m. Service isn't 24/7. As of November 11, 2026, Berto's holds a 5.0 rating from 18 Google reviews. If we've done work for you, you can leave a review.

Gate Welding FAQ

How much does gate welding cost in Vancouver?

Pricing depends on the material, access, how much rust or damage there is, and whether the work is done on site or in the shop. Mobile visits have a 4-hour minimum; shop work has a 2-hour minimum. Call 236-243-8484 for a quote.

Can you repair a sagging or broken gate on site?

Yes. Most hung gates and railings are repaired where they stand, because taking them down often costs more than fixing them in place. Berto's mobile rig comes to your home, strata or building in Vancouver, Burnaby and across the Lower Mainland.

Should I repair my gate or replace it?

Repair makes sense when the frame is still sound and the damage is local: a cracked weld, a torn hinge or a bent section. Replace it when rust has eaten through the frame, posts have failed, or the gate was undersized from the start. We'll tell you honestly.

Do you repair aluminum, steel and wrought iron gates?

Yes. We weld steel, aluminum and wrought iron, plus stainless when that's what you have. The metal matters, so tell us what it is when you book, or send a photo if you're not sure. Aluminum usually needs TIG welding and extra prep.

How long does a gate or railing repair take?

Many on-site repairs are finished in a single visit, within the 4-hour mobile minimum. Heavier rust, a section that has to be fabricated, or a strata site that needs a hot work permit can take longer. Send photos and we'll give you a clearer picture.

Need a Gate or Railing Repaired?

Tell Berto's what's broken and send photos. Pricing is job-dependent, so call for a quote.

236-243-8484